Photo Gallery

1979 GE LU50
GE of America was the first manufacturer to introduce a 50 W high-pressure sodium lamp on the market. The 50 W Lucalox released in 1977 featured an A-shaped outer jacket fitted with an E26 end cap, and a new wire-sealed burner which did not suffer from the thermal limitations that affected early HPS lamps made with the company’s signature external amalgam reservoir. The initial intention was to replace incandescent lamps in applications where light color is not critical. However, this plan did not work out due to too much differences in cost and characteristics between the two lamp technologies. Moreover, the 50 W sodium lamp was notoriously unreliable and its burner was prone to failure early in life.

The reliability issue was eventually solved in late 1979 when the burner construction was updated with GE’s 3rd-gen Lucalox design shown here and first released two years earlier in larger lamps. Improvements in the thermal design enabled the return of a small external reservoir, while the additions of metal foil wraps at the extremities of the arc tube limits end losses. Those heat shields also prevent the condensation of sodium in the seal areas, the primary cause of failure in the previous burner design. Those changes also resulted in the lamp’s initial output to increase by 21 % from 3300 to 4000 lm, thus making it a viable alternative to 100 W mercury lamps and to 207–295 W incandescent lamps that were commonly used to illuminate America’s secondary roads.

The LU50 in the form shown here was GE’s smallest full-sized Lucalox lamp made with the ED23.5 bulb and fitted with a mogul (E39) end cap. That particular lamp design replaced the original one in 1979 when it became clear that its main application would be in street lighting. Typical of US low-wattage sodium lamps, the LU50 has a low arc voltage of 52 V which enables an operation on 120 V mains circuits using a simple and economical series choke ballast. That particular choice in system design certainly contributed to the rapid adoption of this lamp in the early 1980s.


Keywords: Lamps

1979 GE LU50

GE of America was the first manufacturer to introduce a 50 W high-pressure sodium lamp on the market. The 50 W Lucalox released in 1977 featured an A-shaped outer jacket fitted with an E26 end cap, and a new wire-sealed burner which did not suffer from the thermal limitations that affected early HPS lamps made with the company’s signature external amalgam reservoir. The initial intention was to replace incandescent lamps in applications where light color is not critical. However, this plan did not work out due to too much differences in cost and characteristics between the two lamp technologies. Moreover, the 50 W sodium lamp was notoriously unreliable and its burner was prone to failure early in life.

The reliability issue was eventually solved in late 1979 when the burner construction was updated with GE’s 3rd-gen Lucalox design shown here and first released two years earlier in larger lamps. Improvements in the thermal design enabled the return of a small external reservoir, while the additions of metal foil wraps at the extremities of the arc tube limits end losses. Those heat shields also prevent the condensation of sodium in the seal areas, the primary cause of failure in the previous burner design. Those changes also resulted in the lamp’s initial output to increase by 21 % from 3300 to 4000 lm, thus making it a viable alternative to 100 W mercury lamps and to 207–295 W incandescent lamps that were commonly used to illuminate America’s secondary roads.

The LU50 in the form shown here was GE’s smallest full-sized Lucalox lamp made with the ED23.5 bulb and fitted with a mogul (E39) end cap. That particular lamp design replaced the original one in 1979 when it became clear that its main application would be in street lighting. Typical of US low-wattage sodium lamps, the LU50 has a low arc voltage of 52 V which enables an operation on 120 V mains circuits using a simple and economical series choke ballast. That particular choice in system design certainly contributed to the rapid adoption of this lamp in the early 1980s.

Philips_HO_450W_-_NL_1956_a.jpg Orion_HgMIF_400W_-_HU_1989.jpg GE_LU50_-_USA_1979.jpg -_Osram_HQI-BT_40021D_-_DE_1998.jpg -_Narva_HQLS250_-_GDR_1969.jpg
Lamp/Fixture Information
Manufacturer:General Electric
Model Reference:LU50
Lamp
Lamp Type:Sodium high pressure
Filament/Radiator Type:Thermal discharge in xenon, mercury and sodium vapors
File information
Filename:GE_LU50_-_USA_1979.jpg
Album name:Max / Thermal discharge lamps
Keywords:Lamps
Filesize:306 KiB
Date added:Aug 28, 2024
Dimensions:1200 x 634 pixels
Displayed:14 times
DateTime Original:2017:03:05 17:06:44
Exposure Time:1/20 sec
FNumber:f/8
File Source:Digital Still Camera
Flash:No Flash
Focal length:34.3 mm
ISO:400
Model:X-T1
Software:Adobe Photoshop CS5 Windows
White Balance:1
URL:https://trad-lighting.net/gallery/displayimage.php?pid=407
Favorites:Add to Favorites

Comment 1 to 2 of 2
Page: 1

Ria   [Aug 29, 2024 at 12:31 AM]
Lovely little lamp HPS bulb HD

I note that some ratings of US HPS lamps are (or were) available in both low and high arc voltages, what was the reason for this..? Wonder
Max   [Aug 29, 2024 at 08:03 AM]
Good question, to which I don't have a definitive answer. I think this was done to cater to the variety of mains voltage available in the USA other than the standard 120 V (i.e., 240, 277, 408 V) and to offer low-wattage CWA/CWI HPS systems that are more robust toward line voltage variations or drop (e.g. at the end of an installation) than the basic series-choke circuit used with 55 V HPS lamps.

Comment 1 to 2 of 2
Page: 1